Pocket size multimeter is self-contained portable test set that measures a wide range of Voltages, Currents and Resistances. This is an indispensable instrument for servicing and maintenance of electronic equipment, radio and television. The meter is so designed and its movement is heavily damped to avoid damage to the meter movement.

Continuously variable voltage auto transformer, protected type. Comprises a torridly wound transformer with a continuously variable output voltage 0 - 260 volts AC. Steplessly under full load. Input 220 to 240 volts AC, 50 Hz. In stout metal case mounted on a metal base with mains cable

4mm Pin, 18mm long spring insert and hard plastic body. Overall lenght of plug 40mm.

Standard Model Output Voltage/Current

SI 1A 2-12 VDC/3 Amp
SI 12B 2- 12 VDC/4 Amp
SI 12C 2- 12 VDC/5 Amp

To trace Hystersis curves on CRO using Resistance, Capacitance & Inductance.

Instrument comprises of AC Power Supply 10-30 VAC, Output selectable using band switch, Circuit diagram for BH Curve Printed, Components connected behind the front panel, provision for connecting external Inductance, Input & Outputs Connections brought out at Sockets.

To study Frequency Response, Input Impedance, Output Impedance & –ve feed back of common base Transistor Amplifier.

Instrument comprises of DC Regulated Power Supply, Circuit diagram is printed, components mounted on the front panel.

Instrument comprises of DC Regulated Power Supply 0-5VDC/150mA, two round meters (One Voltmeter & One Galvanometer), Three set of resistances mounted behind the panel, connections of supplies, Meters & Resistances brought out at 4mm Sockets. CONVERTION OF GALVANOMETER INTO A CURRENTMETER Instrument comprises of DC Regulated Power Supply 0-5VDC/150mA, two round meters (One milliammeter & One Galvanometer), Three set of Shunts mounted behind the panel, connections of supplies, Meters & Shunts brought out at 4mm Sockets.

DC Regulated Power Supply 1. 0-30V/1.0Amp 2. 0-30V/2.0Amp 3. 0-30V/5.0Amp

Designed with pot core stability for standard laboratory use. Useful as an oscillator element, wave shaping and resonance experiments, bridge experiments. Fuse protection for safety, + 3% accuracy.

Comprises U & I cores of low loss magnetic material, to form a closed core of cross section 25 mm in plane of laminations, 32 mm perpendicular to them is an I - core of length 102 mm. U core external height 102mm. Internal height to take bobbin length 77 mm. Pair of pole pieces, each 65x30x25 mm with on end shaped to part of a cone for maximum flux density. Hole drilled through total length along cone axis to take a light beam. Pole pieces will accept supertrods & shading ring (provided with accessories) & may be clamped on any separation on U core, or in contact as a non laminated I - core. Cast aluminium alloy stand consisting of a heavy base on four rubber feet with removable clamping arms. Maximum dimensions of base 190x200x115 mm. Channel 35 mm wide & 3 mm deep to take transformer core, extends across full width. Integral support for arms, to rear, is below the level of the pole pieces. Arms pivot on steel spindle with adjustment of knobs to rear bringing hard rubber pads at front end of arms to bear on transformer core. Synthetic hammer finish except of clean metal in channel & 4 mm hole to take on earthing plug lead. Complete with all the accessories.

Objective : To plot static & Transfer Characteristics.

Features : Instrument comprises of Two DC Regulated Power Supplies 0-15VDC/ 150mA & 0-5VDC/150mA, three round meters for voltage & current measurement, FET BFW10 mounted behind the panel, connections of Supplies, Meters & FET brought out at 4mm Sockets.

Objective :To study the Frequency and Waveshape generated by a Hartley Oscillator.

Features :Instrument comprises of 30V DC Regulated Power Supply, circuit diagram Printed & components mounted on front panel.

Objective :To plot Frequency Vs. Current Characteristics of LCR circuit when connected in series or in parallel.

Features : Instrument comprises of 3 Resistances, 3 Capacitors & 1 Inductance connected inside & connections brought out at Sockets. 2 AC moving coil meters to measure voltage & current.

Objective :To plot a graph, current Vs intensity of Light at different value of voltages.

Features : Instrument comprises of DC Regulated Power Supply 0-3 VDC/150mA, two round meters for voltage & current measurement, LDR mounted on the panel, connections of Supplies & LDR brought out at 4mm Sockets. Lamp Holder with 60 W Bulb are given with this apparatus.